Metal detector search coils decide how deep, how wide and how precisely your detector searches. A small coil picks good targets out from nearby iron and fits tight spots, and a large coil covers more ground and reaches deeper on larger targets. A coil only fits the detectors it is made for, so check the fit before you order.
The search coil sends the detector's signal into the ground and picks up the response from metal, so its size, shape and winding layout set how deep, how wide and how precisely your detector searches. Changing the coil changes what the detector does best: a large coil for open fields and depth, a small coil for trash and tight spots. We recommend keeping the stock coil for general hunting and adding one coil matched to your hardest sites. Our Search Coil Selection Guide walks through the whole decision; the short version is below.
Search Coil Types Explained: DD, Concentric, Mono and Super-D
Coil type describes how the wire windings inside the coil are laid out, and each layout gives a different detection field.
Coil type
Windings
Detection field
Strengths
Trade-offs
Double-D (DD)
Two overlapping D-shaped windings
Blade-shaped, under the overlapping center of the coil from front to back
Stable over mineralized ground and at the beach; needs less sweep overlap; separates targets lying close together better than a concentric coil of the same size
Less sensitive than a concentric coil of the same size over non-mineralized ground
Concentric
Transmit winding around the outside, receive winding in the center
Cone-shaped and symmetrical
Most accurate pinpointing; consistent target ID
Most affected by ground minerals; needs more sweep overlap
Monoloop (mono)
One winding around the outside that both transmits and receives
Large cone
Typically the best depth
Harder to ground balance in heavily mineralized soil; made for pulse induction detectors
Super-D
One middle transmit winding and two outer receive windings
Acts like two Double-D coils side by side for shallow targets and like one coil for deeper targets
Quieter detecting from electronic calibration; excellent depth
Fits the Minelab GPZ 7000 only
Mono coils are made for pulse induction gold detectors such as the Minelab GPX 6000 and Garrett Axiom, and the Minelab GPZ 8000 uses its own concentric toroidal coils. Two specialist designs sit outside the table: Coiltek builds its Anti-Interference coils for ground with interference from power lines, salt lakes and other sources of electromagnetic interference, and Detech makes S.E.F. coils, such as a butterfly-shaped model for the Teknetics T2. Our blog post DD Coils vs Concentric compares the two most common types in depth, and our detector technologies explainer and how metal detectors work guide cover how a coil creates and reads its field.
Coil Size and Shape: The Trade-Offs
A larger coil covers more ground with each sweep and generally detects deeper, but it is less sensitive to small targets, more affected by electromagnetic interference and reads several targets at once in heavy trash. A smaller coil is more sensitive to small, shallow targets, picks good targets out from iron lying close by and fits confined spots, but it takes more sweeps to cover the same area. We recommend going back over a productive spot with a small coil after a first pass with a larger one. Shape refines the same trade-off: round coils are the most common because they are stable, and elliptical coils are easier to work around bushes and between rocks while covering the same ground as a round coil of the same size. For what a change in depth looks like in practice, see how deep do metal detectors go; depth always depends on target size, ground and settings.
Free Shipping on Orders Over $99: Orders over $99 ship at no extra cost across the continental US.
Authorized Dealer for Every Brand We Carry: Showroom and local pickup in Ypsilanti, Michigan, and the full manufacturer warranty on every coil.
Help Before and After You Buy: Our staff trades coils by site every week. Tell us your detector and the sites you hunt, by phone at (844) 771-0707 or by email, and we will match the coil.
Customer Questions & Expert Answers
Get real answers from outdoor explorers and our product experts. Browse questions about performance, features, and setup —or ask your own to make sure this gear fits your next adventure.
Are metal detector coils interchangeable between brands?
No, metal detector coils are not interchangeable between brands, and often not between models of the same brand. A coil only works on the detectors it is made for: Minelab GPZ 7000 and GPZ 8000 coils are not interchangeable, and neither are GOLD MONSTER 1000 and GOLD MONSTER 2000 coils. Aftermarket brands such as Coiltek, CORS and Detech build coils for specific detectors, for example Coiltek NOX coils for the Minelab EQUINOX, so buy the version made for your model. Check the detectors named on the listing, our What Fits My Detector? finder, or our Minelab, Garrett, Nokta, XP and Fisher compatibility lists, or ask us and we will match the coil to your detector.
Answered by
Dan P.
· November 2026
Does a bigger metal detector coil always go deeper?
A bigger metal detector coil does not always go deeper. A larger coil covers more ground and generally reaches deeper on larger targets, but it is less sensitive to small targets and more affected by electromagnetic interference, so at a noisy site you may have to turn the sensitivity down, and in heavy trash it reads several targets at once. A smaller coil is more sensitive to small, shallow targets. Depth depends on coil, target size, ground and settings together, which is why the right coil depends on the site. For honest numbers, see how deep do metal detectors go, and use our Search Coil Selection Guide to match a coil size to your sites.
Answered by
John W.
· November 2026
What's the difference between DD and concentric coils?
The difference between DD and concentric coils is the shape of the detection field. A DD (Double-D) coil has two overlapping D-shaped windings that send a blade-shaped field down the center of the coil from front to back; it runs stable over mineralized ground and at the beach, needs less sweep overlap and separates targets lying close together better than a concentric coil of the same size. A concentric coil has a transmit winding around the outside and a receive winding in the center, giving a cone-shaped field that pinpoints most accurately and is more sensitive than a DD of the same size over non-mineralized ground, but it is the most affected by ground minerals. Read DD Coils vs Concentric for the full comparison, and our detector technologies explainer for how each coil creates and reads its field.
Answered by
Richard T.
· November 2026
Do I need a coil cover for my metal detector?
You need a coil cover for your metal detector if you scrub the coil over rocks, gravel or hard ground. A cover takes the wear that would otherwise land on the coil housing. Every Minelab coil comes with a coil cover, and many other coils do too; when you replace one, match the cover to your exact coil model and size. Find them by size and model in our coil covers.
Answered by
Dan P.
· November 2026
Why buy an aftermarket metal detector coil instead of OEM?
The reason to buy an aftermarket metal detector coil instead of OEM is more choice of size, shape and type for your model. OEM coils are made by the detector's own maker, such as Minelab, Garrett and Nokta. Aftermarket makers such as Coiltek, CORS and Detech build coils for specific detectors, for example the CORS Giant 15 x 17 inch coil for the Minelab X-TERRA or Coiltek's Anti-Interference coils for Minelab SD, GP and GPX detectors other than the GPX 6000. Confirm the fit in our What Fits My Detector? finder or ask us before ordering.
Answered by
John W.
· November 2026
Should I use a smaller coil in trashy parks?
Yes, a smaller coil is usually the better choice in trashy parks. A small coil sees less ground at once, so it can pick out a coin or ring lying close to a pull tab or nail, and it is more sensitive to small, shallow targets. Small coils also fit between roots, benches and fences more easily. Garrett, for example, recommends its Super Sniper coil for trashy areas on the AT Max. The trade-off is slower ground coverage, so we recommend carrying a small coil for trashy spots and a standard coil for open ground. Our Search Coil Selection Guide helps you choose size and shape.
Answered by
Richard T.
· November 2026
What does the search coil on a metal detector do?
The search coil on a metal detector sends the detector's signal into the ground and picks up the response when metal is under it. Inside the coil are wire windings that transmit and receive: a concentric coil has a transmit winding around the outside and a receive winding in the center, a Double-D coil has two overlapping D-shaped windings, and a monoloop coil uses one winding that both transmits and receives. The layout and size of those windings set how deep, how wide and how precisely the detector searches, which is why a different coil changes what the detector does best. Our Search Coil Selection Guide and how metal detectors work guide explain more.
Answered by
Dan P.
· November 2026
Subscribe to our newsletter
Get an instant Discount Code, the latest detecting and prospecting drops, exclusive offers, and pro tips, straight to your inbox.