XP Deus Certified Underwater Water Kit for LCD Remote and WS-4 Control Pod

This XP certified underwater kit is compatible with the XP Deus (all versions that use the LCD remote control or WS-4 control pod) and the XP ORX detector. The kit works with any Deus coil because the aerial antenna clips to the coil cover regardless of coil size or frequency. The waterproof armband case fits both the Deus LCD remote and the WS-4 headset, so you can run either control configuration underwater. The waveguide antenna maintains signal integrity for both the Deus and ORX detector families when submerged. If you're running a different XP model or a non-XP detector, verify compatibility with XP metal detectors before ordering.

The XP Deus underwater kit is rated for submersion to 5 meters (16 feet) when all components are properly installed. The waterproof armband case protects the LCD remote or WS-4 control pod to that depth, and the aerial antenna maintains radio communication between the coil and remote throughout the water column. Most detectorists use this kit in surf zones, rivers, and shallow lakes where hunting depths range from knee-deep to chest-deep, well within the 5-meter rating. The kit brings the remote's protection level up to match underwater detecting requirements, allowing you to work confidently in deeper water environments.

The waterproof armband case is required for full immersion (deeper than 50 centimeters or when you're diving), but partial-immersion setups allow stem-mounted remote configurations. XP's documentation shows a stem-mount option where the remote stays above the waterline and the aerial antenna clips to the stem or headphones, suitable for knee-deep wading in creeks and rivers. The case becomes mandatory when you're working waist-deep surf or diving in freshwater lakes, because any accidental submersion of an unprotected remote will flood the electronics. The inline volume control works in both mounting styles, so you can adjust headphone output without opening the case or reaching for the remote.

The aerial antenna (waveguide) clips to the search coil cover on the same side as the coil's battery terminals using the supplied plastic support clip and O-rings. Remove the adhesive backing from the support clip, position it on the coil cover near the cable exit point, and press firmly to secure. Thread the coaxial cable along the detector shaft using the additional support clips (you get three total), and route the cable to the waterproof armband on your forearm or to the stem-mounted remote depending on your immersion depth. The O-rings attach the antenna securely to the coil so it doesn't shift during recovery swings. The kit includes mounting hardware for coil-mount, stem-mount, and armband-mount configurations.

The aerial antenna (waveguide) is designed to maintain the radio link between the coil and remote or WS-4 headset when submerged, carrying digital data including target ID, audio, and threshold information. The 8-foot cable length is sufficient for standard swing arcs, and the thin coaxial design doesn't add meaningful drag in the water column. The waveguide antenna routes communication signals from the coil's processor to your control unit, allowing the detector to function normally in underwater environments. XP engineered the antenna system specifically to preserve detector operation at depths up to 5 meters.

You must use waterproof headphones when the detector is fully submerged, and the kit includes a waterproof headphone set with an inline volume control adapter. For partial immersion (coil underwater, remote above water on the stem), you can continue using your standard headphones because they stay dry. The included waterproof headphones connect through the inline volume control, which plugs into the waterproof case's headphone port. The inline volume control works with both the waterproof headphones and standard Deus audio accessories, giving you adjustment range without opening the case. Explore additional audio options in our metal detector parts and accessories catalog.

The waterproof armband case has a transparent window that allows touchscreen interaction with the remote while sealed. Most underwater hunters preset their program (Beach, Diving, or a custom profile) before entering the water and rely on the inline volume control for audio adjustments during the hunt, minimizing the need for mid-session menu changes. The case's armband strap keeps the remote accessible on your forearm, so you can glance at the screen for target ID without pulling the detector from the water. The transparent window design balances waterproof protection with operational access to the LCD remote's controls.